21 of 22 would recommend this product to a friend.
Product Reviews
FEATURED REVIEW
Overall Rating:
5
/ 5
outstanding value,
July 9, 2007
By dogmanfrom scranton, pa
"I recently purchased two of your needle guns. One as a back-up. However after almost thirty hrs. of usage the first needle gun is still going strong and should finish the job of scaling off globs of rust from a decorative iron fence. It has easily taken off old primer, paint and rust down to bare metal. I never expected such a quality product for the price. If it's bare metal your looking for, then this is the tool. Thank-you for delivering such an outstanding product!"
What is your level of technical expertise?:
Professional
Overall Rating:
4
/ 5
Great Tool,
August 18, 2008
By Benzfrom North Dakota
"The needle scaler worked very well for removing paint from a concrete floor. I was worried about having to use chemicals to do the job, and in the end, I didn't have to. The price is great.....didn't think it would work as well as it did."
What is your level of technical expertise?:
Home Handyman
Overall Rating:
4
/ 5
NT Needle Scaler,
August 18, 2008
By Ranger58from Greensboro, NC
"I bought this tool to clean the rust off of some old trailer wheels so I could repaint them. Without this tool, I was unable to get into all of the tight crevices. The project turned out great. I am planning on cleaning up some iron railings next. I didn't know what I was missing. Glad to own it!"
What is your level of technical expertise?:
Home Handyman
Overall Rating:
5
/ 5
Needle Scaler Review,
August 11, 2008
By sccrooksfrom Rehoboth, MA
"A tremendous timesaver, but be sure to buy hearing protection if you don't already have it...this is a noisy tool. Bought to work on restoring antique tractors and it does a tremendous job of getting old paint (often very heavy coats) off cast parts...does not work well on sheet metal ...metal vibrates too much. Can't be beat for the price."
What is your level of technical expertise?:
Beginner
Overall Rating:
5
/ 5
Great Tool,
April 23, 2008
By Ford350from New York State
"This needle scaler is a great addition to any tool box. I used it to clean up the frame on my pick up truck. It cleans the rust around rivets and curved areas with ease. There is no other tool that does what this scaler can do."
What is your level of technical expertise?:
Home Handyman
Overall Rating:
5
/ 5
Air Needle Scaler,
April 22, 2008
By Plowman88from maine
"I bought this tool to remove the rust that had built up on the frame of my plow truck. I wanted to clean the frame up to prep it for paint. Sure beat doing it by hand with a scraper,wire brush and hammer. Worked excellent and for the money it was well worth it."
What is your level of technical expertise?:
Home Handyman
Overall Rating:
5
/ 5
Hard working,
April 21, 2008
By Maintenance101from Duluth Mn.
"We picked one of these up for removing paint and rust from steel and concrete stairs. It did an exelent job removing all the old paint,rust from the railing and the stair treads. With all the old paint gone the new coat looks 100 times better because there is no high spots. It left a even level serface behind. Since then we have used it for other jobs and it has held up great."
What is your level of technical expertise?:
Professional
Overall Rating:
4
/ 5
Problem Solver,
April 21, 2008
By Wendelfrom New Philadelphia, OH
"Made quick work of removing old paint and rust from angle iron top plate over a large Pella siding door unit installed on a brick house. I had trouble controlling grinding wheels and sanders as their torque risked damaging the wooden trim of the door unt. This thing worked very, very well without the collateral damage, and I could remove paint all the way into the corners of the frame. This is almost impossible unless using a small grinder or ossillating detail sander. The unit came without any directions, just a parts list. Make sure you tighten the three allen screws down after installing the needle scaler, or you will be chasing them over the floor when you first pull the trigger. Eye protection is a must if you are using the product at head level or above your head as I was. The chips fly in a circular pattern away from the tool. Very good product. Instruction manual would be a great help to the non-professional."
What is your level of technical expertise?:
Home Handyman
Overall Rating:
5
/ 5
great value,
April 14, 2008
By Grassonefrom New Hampshire
"I,m a landscape contractor and purchased this needle gun to prep my dump bed for repainting, and it did its job with no problems. since finishing the dump i have used it to prep two plows ,tractor, and other misc equipment with heavy rust scale to prep for paint this item has done much more work with out a failure than could be exspected for a tool this inexpensive. IT WON'T DISAPOINT YOU SO BUY WITH CONFIDENCE!!!!!!!!!!!!"
What is your level of technical expertise?:
Professional
Overall Rating:
5
/ 5
air needle scaler,
April 14, 2008
By 58buickfrom California
"I bought the air needle scale after reading a web page that suggested using it to remove the grease and grim build up on the under carriage of a car. I bought the needle scaler and statrted using it on a 1958 buick that I'm restoring. The needle scaler did the job in a fration of the time it had been taking me and left the under carriage and chassis twice as clean. I would recommend this item to anyone that was going to tackle a simular project."
What is your level of technical expertise?:
Beginner
